Standard Two-Wire Field-Programmable
Chopper-Stabilized Unipolar Hall Effect Switch
A1184
11
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
V
PH
V+
t
V
PM
V
PL
0
Encode 00100
2
(4
10
)
Enable
Address
Address
Blow
Blow
Enable
Encode 00001
2
(1
10
)
Figure 6. Pulse sequence to permanently encode calibration value 5 (101 binary, or
bitfield address 3 and bitfield address 1).
V
PH
V+
t
V
PM
V
PL
0
Try 5
10
Enable
Address
Clear
Optional
Monitoring
The pulse sequences consist of the following groups of pulses:
1. An enable sequence.
2. A bitfield address sequence.
3. When permanently setting the bitfield, a long V
PH
fuse-blow-
ing pulse. (Note: Blown bit fuses cannot be reset.)
4. When permanently setting the bitfield, the level of V
CC
must
be allowed to drop to zero between each pulse sequence, in
order to clear all registers. However, when provisionally set-
ting bitfields, V
CC
must be maintained at V
PL
between pulse
sequences, in order to maintain the prior bitfield settings while
preparing to set additional bitfields.
Bitfields that are not set are evaluated as zeros. The bitfield-level
fuses for 0 value bitfields are never blown. This prevents inad-
vertently setting the bitfield to 1. Instead, blowing the device-
level fuse protects the 0 bitfields from being accidentally set in
the future.
When provisionally trying the calibration value, one pulse
sequence is used, using decimal values. The sequence for setting
the value 5
10
is shown in figure 5.
When permanently setting values, the bitfields must be set indi-
vidually, and 5
10
must be programmed as binary 101. Bit 3 is
set to 1 (000100
2
, which is 4
10
), then bit 1 is set to 1 (000001
2
,
which is 1
10
). Bit 2 is ignored, and so remains 0.Two pulse
sequences for permanently setting the calibration value 5 are
shown in figure 6. The final V
PH
pulse is maintained for a longer
period, enough to blow the corresponding bitfield-level fuse.
Figure 5. Pulse sequence to provisionally try calibration value 5.
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
A1186LUA-T
IC SWITCH HALL EFFECT UNI 3-SIP
A1193LUA-T
IC SW HALL EFFECT CHOPPER 3SIP
A1203LUA-T
IC SW CONTINUOUS TIME BIPO 3-SIP
A1205EUA-T
IC SWITCH HALL EFFECT GP 3-SIP
A1211LUA-T
IC LATCH HALL EFFECT 3-SIP
A1220LUA-T
IC HALL EFFECT LATCH 3V 3-SIP
A1242LUA-I2-T
IC LATCH HALL EFFECT 3-SIP
A1244LUA-I2-T
IC HALL EFFECT LATCH SIP-3
相关代理商/技术参数
A1185
制造商:Quick 功能描述:TSOJ 13 X 10 NOZZLE FOR QUICK957/957D
A118-5
制造商:APEM 功能描述:
A1185_06
制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Ultrasensitive Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches
A1185B
制造商:HAKKO Corporation 功能描述:
A1185ELHLT
功能描述:IC SWITCH HALL EFFECT UNI SOT-23 RoHS:否 类别:传感器，转换器 >> 磁性 - 霍尔效应，数字式开关，线性，罗盘 (IC) 系列:- 标准包装:1 系列:- 传感范围:20mT ~ 80mT 类型:旋转 电源电压:4.5 V ~ 5.5 V 电流 - 电源:15mA 电流 - 输出（最大）:- 输出类型:数字式，PWM，8.5 位串行 特点:可编程 工作温度:-40°C ~ 150°C 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:Digi-Reel® 其它名称:AS5132-HSST-500DKR
A1185ELHLT-T
功能描述:IC SWITCH HALL EFFECT UNI SOT-23 RoHS:是 类别:传感器，转换器 >> 磁性 - 霍尔效应，数字式开关，线性，罗盘 (IC) 系列:- 标准包装:1 系列:- 传感范围:20mT ~ 80mT 类型:旋转 电源电压:4.5 V ~ 5.5 V 电流 - 电源:15mA 电流 - 输出（最大）:- 输出类型:数字式，PWM，8.5 位串行 特点:可编程 工作温度:-40°C ~ 150°C 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:Digi-Reel® 其它名称:AS5132-HSST-500DKR
A1185EUA
功能描述:IC SWITCH HALL EFFECT UNI 3-SIP RoHS:否 类别:传感器，转换器 >> 磁性 - 霍尔效应，数字式开关，线性，罗盘 (IC) 系列:- 标准包装:1 系列:- 传感范围:20mT ~ 80mT 类型:旋转 电源电压:4.5 V ~ 5.5 V 电流 - 电源:15mA 电流 - 输出（最大）:- 输出类型:数字式，PWM，8.5 位串行 特点:可编程 工作温度:-40°C ~ 150°C 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:Digi-Reel® 其它名称:AS5132-HSST-500DKR
A1185EUA-T
功能描述:IC SWITCH HALL EFFECT UNI 3-SIP RoHS:是 类别:传感器，转换器 >> 磁性 - 霍尔效应，数字式开关，线性，罗盘 (IC) 系列:- 标准包装:1 系列:- 传感范围:20mT ~ 80mT 类型:旋转 电源电压:4.5 V ~ 5.5 V 电流 - 电源:15mA 电流 - 输出（最大）:- 输出类型:数字式，PWM，8.5 位串行 特点:可编程 工作温度:-40°C ~ 150°C 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:Digi-Reel® 其它名称:AS5132-HSST-500DKR